Since 2008, the company has broadened the product line to add J-B SteelStik, KwikWood, PlasticWeld, MarineWeld, Perm-O-Seal, WoodWeld and ClearWeld. [5] [6] J-B Weld epoxy [ edit ] PRODUCT FEATURES AND STRENGTH: J-B Weld SteelStik has lap shear strength of 900 PSI, can withstand continuous temperatures up to 350F (176C ) and intermittent temperatures of 450F (232C), and is chemical resistant against petroleum, hydraulic fluids and other chemicals when fully cured. SteelStik can be molded, shaped, sanded, drilled and tapped. CURE AND SET TIME: After mixing the tubes at a 1:1 ratio, it takes 4-6 hours to set and 15-24 hours to cure. Once cured J-B Weld Original can be tapped, filled, sanded, molded and drilled. J-B Weld Original set and cure color is dark grey. Sampson, William (September 16, 2013). "In the Shop: Wood repair products from J-B Weld". www.fdmcdigital.com. CabinetMakerFDM . Retrieved March 27, 2015.

CURE AND SET TIME: After kneading the two part formula together by hand, SteelStik takes 5 minutes to set and cures in 1 hour. J-B Weld SteelStik set and cure color is dark grey. This article relies excessively on references to primary sources. Please improve this article by adding secondary or tertiary sources. SURFACE APPLICATIONS: Iron & Stainless Steel, Copper & Brass, Aluminum & Bronze, Fiberglass and Plastic & PVC.Most epoxies add strength to a joint when the epoxy-joint layer is minimized. Epoxy, in and of itself, doesn’t carry strength. Its the cross-linking nature of the epoxy establishing bonds between the materials forming the joint. Long spans (think gaps) between the articles forming the joint creates a weak bond- the epoxy is making longer bonds to the materials to be joined. A thin gap is best. JB Weld has small metallic materials in suspension, so some gap filling will work with this original formulation. VERSATILE AND DEPENDABLE: J-B Weld Original is steel reinforced, has a tensile strength of 5020 PSI and can withstand temperatures up to 550 degrees Fahrenheit (287 degrees Celsius. When fully cured, J-B Weld Original is waterproof and resistant to petroleum, chemical and acid. CURE AND SET TIME: After kneading the two part formula together by hand, WaterWeld takes 25 minutes to set and cures in 1 hour. J-B Weld WaterWeld set and cure color is off white. J-B Weld is a two-part epoxy adhesive (or filler) that can withstand high-temperature environments.

The mixture will set enough for the glued parts to be handled within 4–6 hours, [7] but requires up to 15 hours at cool temperatures to fully cure and harden. Temperatures above 50°F (10°C) shorten all these times. [7] This technology we use to assemble our list depends on a variety of factors, including but not limited to the following:Apply the resin to both surfaces to be joined and clamp or tape the parts together until Super Steel has set hard. The epoxies tested include Gorilla epoxy, Devcon Plastic Steel, Loctite Epoxy Weld, JB Weld original, JB Weld Kwik Weld, and JB ExtremeHeat. This more or less covers the entire gamut of epoxies you would find in the glue aisle of your local home supply store; the Gorilla epoxy is your basic 5-minute epoxy that comes in a double barrel syringe, and the JB Welds are the cream of the crop. Applications: Abs, Pvc & Cpvc Pipes And Plastics, Auto Bumpers And Trim, Vinyl Surfaces And Siding, Marine Repairs & Fiberglass Parts, Plastic Water Tanks, And Plumbing

PRODUCT FEATURES AND STRENGTH: J-B Weld WaterWeld has lap shear strength of 1300 PSI, can withstand continuous temperatures up to 300F (149C) and intermittent temperatures of 350F (176 degrees Celsius) and is chemical resistant against petroleum, hydraulic fluids and other chemicals when fully cured. J-B Kwik (stylized as J-B KWIK) is a two-part epoxy, intended as an adhesive or filler, that can withstand medium-temperature environments (up to 300°F or 149°C). [14] J-B Weld can be used as an adhesive, laminate, plug, filler, sealant, or electrical insulator. [8] When fully cured, J-B Weld can be drilled, formed, ground, tapped, machined, sanded, and painted. [8]But an oil leak onto the exhaust threatened to derail the trip. The leak was due to the valve cover stud in the lower left corner of the head being stripped in its hole and thus not tightening, which prevented that corner of the valve cover from sealing. This caused oil to drip directly onto the downpipe, which was a clear fire hazard. At the time, I repaired the stripped threads with a Time-Sert (helicoil). The car still appeared to be weeping a small amount of oil through the threads onto one of the exhaust studs, but this is a common problem, as the lower exhaust studs thread directly into oil runoff area on the low side of the head. I made it home without incident, and that spring I road-tripped the car 2000 more miles to other events. Two-part epoxy is one of those must-have items in your toolbox, albeit kept in a ziploc bag to keep all that goo off the rest of your tools. It’s a glue with a million uses, but which brand is best? Should you keep some cheap five-minute epoxy around, or should you splurge for the fancy, long-setting JB Weld. It’s not a perfect analysis, but at least [Project Farm] has done the experiment. This is a test of which two-part epoxy you can find at your local home supply store is strongest. I made it 230 miles to Harmony, Pennsylvania, by nightfall, and I pounded out the remaining 620 miles to Boston the following day without incident. The J-B Weld Company's original product line focused on a small number of products: J-B Weld (original 2-tube epoxy), J-B Kwik (4-hour epoxy), J-B Stik ( epoxy putty), Waterweld (underwater adhesive/filler), and a few others. [4] The Plastic Padding Super Steel Epoxy Weld is a dark-grey coloured, metal-filled, two-component adhesive, which sets like steel and is ideal for emergency repairs around the home, garden, farm, car, boat etc.