If you are having problems connecting your Bluetooth device to the AXR, please try the following troubleshooting steps:

The Cambridge Audio AX Series is being joined by a powerful all-rounder, as promised by the English hi-fi manufacturer Cambridge Audio. With an excellent price/performance ratio, the new Cambridge Audio AXR100D is set to prove a perfect start to the hi-fi world of “Great British Sound”. The tuner will stop at the first strong signal it finds. To move to another station simply press the reverse or forward ‘Skip/Scan’ button again. Note: To add another Bluetooth device, Press and hold the Bluetooth/Phono button to disconnect the current connection and repeat step 2. To enter the audio menu. Press either the Menu button on the front of the unit or on the remote control.Isolate one of the ground paths with an isolation transformer, common mode choke, optical coupler, balanced circuitry, or frequency selective grounding.

At the heart of the new Cambridge Audio AXR100D is a stereo integrated amplifier, which should have sufficient power reserves to operate even stand-alone speaker systems, in any case fine compact bookshelf speaker systems, effortlessly. Two times 100 Watts are available here at loudspeaker systems with an impedance of 8 Ohm. A typical living room is thus easily provided with adequate sound, and should even more bass be desired, an additional subwoofer can of course be controlled via a corresponding pre-amplifier output.Once you have stripped the outer insulation of the cable and twisted the wires as indicated below, securely connect these to your banana plugs, remove the dust cap from the end of the speaker terminal and push the plug in as far as possible without applying excessive force. Two settings are possible which set the correct de-emphasis and tuning steps for either North America or Europe/Rest of the world. If your loudspeakers are equipped with two sets of terminals, then it is possible to connect them in the bi-wire configuration.

Cambridge Audio delivers yet another stunning effort for hi-fi enthusiasts of all types and budgets with the AXR85. Use either the Volume Up/Down buttons on the remote control, or the Volume control on the front panel of your unit to change the volume level. The newly selected level will be indicated briefly on the front display.Cambridge had already developed a state-of-the-art CD driver known as their S3 Servo for their high-end AZUR series. This is the same drive in the CXC. It has levels of jitter rejection and error correction that you might see in multi-thousand dollar CD drives. They also designed the chassis to be very well isolated so that external vibrations that could affect performance are minimized. You will just not find better CD transport out there for under two thousand dollars in our opinion. Cambridge Audio CXN V2 Prepare the speaker cords for connection by stripping off approximately 10mm (3/8”) or less of the outer insulation. More than 10mm could cause a short circuit. Twist the wires tightly together so there are no loose ends. Unscrew the speaker terminal, insert the speaker cable, tighten the terminal and secure the cable. First, I’ll go over the things both product ranges have in common. With four models in each lineup, I thought it was pretty neat that Cambridge Audio decided to give both series the same cosmetic appearance, so you can easily mix and match them. All eight products come in a new lunar gray finish and have a floating look from the front. All of the amplifiers and the receivers use their classic toroidal power transformer for better sound. The CXN V2 uses dual Wolfson WM8740 24-bit DACs. These are even better than the ones in the CXA81. But if you wanted to use it as a streaming source with a very high-end multi-thousand dollar DAC, it gives you both Toslink and coaxial digital outputs. Cambridge Audio also understands you may have more digital sources you want to run through the unit. So they give you a coaxial and Toslink digital input. For connecting it to your integrated amp or preamp, You have both balanced and RCA outputs. The final icing on the cake is that you can set up the CXN V2 to have either fixed or variable output. This means you could use it in the fixed output mode to run into your integrated amp or preamp. But if you just wanted a digital-only system, you can connect it directly to a power amp. The CXN V2 is just flat out an incredible product for the money. You can use it with any system and in a variety of ways. Conclusion Press the Source button on the front of the unit corresponding to your desired source. Alternatively, you may use the appropriate button on the remote control.

It seems like Cambridge have raised the bar again with their new AX range and the value for money has proven to be absolutely top notch. If you want a bit of everything from your hi-fi but are on a limited budget, the AXR85 surely has to be one to listen to with your own ears. As ever, if it sounds like the piece of the puzzle that you’re looking for why not make an appointment at your local Richer Sounds for a demo?

Social Media

Select the Tuner source using the FM/AM button on the front of the unit, or directly by pressing the FM or AM buttons on the remote. To assign a radio station to a preset, or reallocate an existing preset to a new preset location, please follow the steps below, whilst listening to the frequency or station you wish to store: When you wish to make an adjustment for bass, treble or balance, simply rotate the Volume control or use the Volume control buttons on the remote control.