Mapei Mapesil AC 111 Solvent-Free Silicone Silver Grey 310ml

Product Information

Mapei Mapesil LM Silicone Sealant is a neutral, mould-resistant silicone sealant with very low emission level of volatile organic compounds (VOC), for use with natural stone and marble.

Mapei Mapesil AC Silicone is a one-component, acetic crosslinking, solvent-free silicone sealant, available coloured or transparent. It is a thixotropic paste which is easily trowellable both horizontally and vertically. Mapei Mapesil AC Silicone crosslinks following exposure to atmospheric humidity at ambient temperatures, and forms an elastic product with following properties:To control the depth of the joint and to prevent Mapei Mapesil AC Silicone from adhering to the base, the bottom of the joint should be filled with a sized Mapefoam, a polyethylene cord

Mapei Mapesil LM Silicone delays the formation of surface mould. Mapei Mapesil LM generally offers good resistance to chemical agents. However, because of the wide range of products and service conditions, if in doubt carry out preliminary tests beforehand. Forming a perfectly elastic gasket between different elements in building, mechanical engineering, ship-building, automobile manufacturing, etc. Mapei Mapesil LM is particularly suitable for surfaces sensitive to acids on which conventional neutral or acid sealants normally provoke changes in colour or staining of the substrate. Under certain conditions Mapei Mapesil LM Silicone may have a water-repellent effect along the edges of joints. This effect is only noticeable when surfaces are wet and is invisible when the same surfaces are dry. This phenomenon, however, has no effect on the product’s performance characteristics. Do not use Mapei Primer FD when sealing stone or marble.

Follow Us:

Sealing joints between sinks or sanitary ware and ceramic tiles in kitchens, bathrooms and showers with colours coordinated with the grouts. Do not use Mapei Mapesil LM for sealing doors subject to intense traffic – (use Mapeflex PU45, Mapeflex PU20 or Mapeflex PU21). Make sure your tiling project’s joints and seals stand up to everyday wear and tear with Mapesil, an acetic-crosslinking silicone sealant from the world’s leading manufacturer of tiling grout, adhesives and sealing products, Mapei. When Mapei Mapesil LM is exposed to the air, the surrounding humidity sets off the cure reaction and the sealant becomes flexible. The surrounding temperature only has a small impact on the cure rate of Mapei Mapesil LM, while the level of humidity in the surrounding air has the most influence. We highly recommend that the product is never applied if the temperature is below 0°C.

For sealing surfaces sensitive to acids such as lime stone, use a neutral silicone sealant (e.g. Mapesil LM). Thanks to the low modulus of elasticity of Mapei Mapesil LM Silicone, it is suitable for sealing internal and external fillet and expansion joints, including those subject to high levels of movement when in service, between: Pre-fabricated panels, window/door fittings and wall surrounds, pipe-work and vertical walls, similar and/or different types of coating materials. It is also suitable for sealing joints in doors with limited pedestrian traffic. Where Mapei Mapesil AC is to be applied in areas of continuous immersion, i.e. inside a swimming pool tank, the joints must be primed using Mapei Primer FD. Application of Mapei Primer FD: Where the use of Primer FD is necessary, it must be applied with a small brush onto the appropriate areas of the joints and left to dry for several minutes to allow the solvent to evaporate. Then apply Mapei Mapesil AC Silicone. the joint is sized so that the estimated maximum extension is not greater than 25% of the initial width (calculated at +20°C);When Mapesil LM is constantly immersed in treated water typically found in swimming pools its physical-mechanics may be affected prematurely. Given the wide range of products used to treat water and the actual quantities employed, its suitability over long periods may only be guaranteed following specific laboratory testing. The use of Mapei Mapesil AC is not recommended on highly plasticised material or on bituminous surfaces because of the release of substances that reduce bonding and penetrate into the sealant, altering the colour and resistance.