God Hand PN-120 single-edged nippers

Product Information

If the cutting edge and the cutting board edge are aligned, even the slightest misuse will result in the edges being off. Shave & Cut” structure allows a smooth cut surface as if it is cut off by a design knife and it minimizes plastic whitening. Single Edged Structure is where one blade is the “Cutting Edge” and the other blade is the “Cutting board Edge”, like a knife and a cutting board. There also consider the durability of our customers to focus on next sharpness degradation of sharpness. When the cutting edge and the cutting board edge are not aligned, it will result in an unclean cut and possible chipping and breaking of the blades.

Ultra-thin “cutting edge” is created one by one by a well experienced craftsmanship in Tsubame-Sanjo, Niigata prefecture, Japan. So amazed that I decide to leave this review, and to even go the extra distance and include images to compare the two brands. The images may be grainy because they are very close images of a very small sprue, but you get the idea from them. The two with a 'T' written on them are the Tamiya snips, the three without are from the God Hands. I included head on pics as well as from the side which is better at showing how smooth the cut is. Ultimate Nipper’s superior sharpness comes from its thinly refined cutting edge and single-edge structure for a clean cutting. The blade is thinner toward the tip and is more likely to break. Please cut as close to the center of the blade as possible.Poor lubrication of moving parts causes wears on the shaft and rattling, leading to reduced sharpness. Please lubricate the moving parts regularly. Please do not twist the blade during cutting or releasing from the runner. Twisting may cause it to break under load. It is created one by one through blade edging and sharpening by well-experienced craftspersons in Tsubame-Sanjo, Niigata Prefecture, a region famous for its cutlery. Please do not cut plastics that are too long for the blade. The load will be applied to one point, causing it to break or bend. NOTE :หากสั่งสินค้าพร้อมส่งกับสินค้าพรีออเดอร์ในบิลเดียวกันจะรอจัดส่งพร้อมกันเมื่อสินค้าพรีออเดอร์มาครบแล้วนะคะ

All in all, the GodHand SPN-120 is an amazing tool and a must-have for anyone serious about Gundam or models in general. 5 out of 5. Compared to a standard nipper, the section that is cut has a clean surface which is beneficial to those who want to finish the plastic models without painting. Here’s all four of the side cutters I use regularly. Left: God Hand. Top: Tamiya. Right: Mr. Super Tool Set. Bottom: Gundam Planet. Notice how obvious it is that the God Hand has the shortest and smallest (but by far the sharpest) blades of them all.The wide cutting board edge supports an object firmly leading to minimum deformaties due to cutting. The sharpness of the cutting edge achieves a smooth cut surface as if sharpened with a design knife and minimizes plastic whitening (a phenomenon in which the cut section turns white). In case the product, there may be cases, under certain situations, where the delivery date is changed or delayed ,we, VCAGUNDAM.com cannot take responsible for any loss or detriment involved in the use of the service. Single-edged blade structure refers to a design in which one side of the blade is a cutting blade, and the other side is a cutting board blade. The blade is named ‘single-edged’ because only one blade (cutting edge) cuts on one side.

Being the nerd that I am I took them both to my wife and had her use the Tamiya snips first, no problem, they worked as expected. Then I handed her the God Hands and had her do another cut; her response was "wow!". She then proceeded to cut the rest of the sprue into bits just because it is amazing how easy it is to do. Literally like as close to zero resistance as you can possibly get in a world subject to the laws of physics. For those who paint plastic models, the cutting surface remains smooth and clean even if the blade is cut along the part without leaving a gate, thus shortening the time for gate processing with files or knives. Usually, when I cut pieces out of the sprue, I leave a small nub that I can then cut off with an X-Acto knife. But the God Hand is so sharp and narrow that it can get right up against the part, allowing me to skip the knife step. With the God Hand, my process is this:

For people who paint plastic models, this is the best nipper to use because when they cut along the edge, it leaves no remains of the gate. It leaves with a clean cut section. This shortens the time spent on filing the gate. The blade can cut plastics with ease and precision. Please do not grip the nippers with excessive force. If I make sure I’m holding the nippers exactly parallel with the part, I don’t leave an indent or raised angle. If I do it right, I can skip right to filing or sanding. To see just how small, here’s the God Hand next to my second slimmest pair, my Gundam Planet premium side cutters. (In a way this is a great recommendation of the Gundam Planet side cutters as a budget alternative, because look at how similar they are to nippers twice their price!) The standard force for cutting 3 mm dia. plastic is 2 kg or less. (General nippers are 3.5 kg to 10 kg)

Not for photo etched parts Ultra thin single edged! Ultimate Sharpness! . Ultra thin single edged brings excellent performance with less work time! The cutting board edge supports an object firmly while the gripping force changes to move the cutting edge smoothly. Compared to most nippers, the cut surface is much cleaner and neater, which makes it a good choice for those who want to complete plastic models without painting. We're not just making that up - Pete, James and Foxx have sworn by them for years and we are ridiculously excited to be able to bring them to you now. They truly are tools that are at home whether they are in the hands of a beginner or a professional. These are not mass-produced throwaway tools; they are tools designed by and for master craftsmen that will enable you to create incredible art.Ultimate Ultra-Thin Single-Edge! Ultimate Sharpness!When trying to slice-cut a 3 mm dia. runner, the blade moves in smoothly and finishes cutting without sound.